LG vacuuum pump
LG vacuuum pump
Sliding vane rotary vacuuum pump
2X Sliding vane rotary vacuuum pump
XD Sliding vane rotary vacuuum pump
Water ring vacuuum pump
2SK Two-stage Water ring vacuuum pump
SK Water ring vacuuum pump
SZ Water ring vacuuum pump
2BE Water ring vacuuum pump
Piston vacuuum pump
WLW Oil-free vertical Piston vacuuum pump
Roots vacuuum pump
ZJ Roots vacuuum pump
System
JZJS Roots vacuuum pump System
JZJX Roots vacuuum pump System
JZJW Roots vacuuum pump System
J2SK JSK J2BE Closed cycle System
Blow Molding Machine
YX1200 Large hollow blow molding Machine
WUXI CITY SIFANG VACUUM EQUIPMENT CO.,LTD.
WEB:http://www.sfpumps.com.cn
E-MAIL:sfpumps@163.com
TEL:0510-85990421 85990035
FAX:0510-85993842
ADD:No.48 Changkang Road, Mashan, Binhu District, Wuxi
 
Products
Contents brief introduction
XDSeries

Sliding vane rotary vacuum pumps

        

  Instruction of working principle of sliding vane rotary vacuum pumps
The functional diagram of rotating vane pumps is shown in the figure. The rotating vane pump mainly consists of the stator, rotor, rotary vane, fixed cover, spring and components. The structure is formed by rotor which eccentricly installed in the chamber of the stator (the outer circle of the stator is tangental to the inner surface of rotor, and the gap between the two is very small) and the two rotary vanes which adhere to the inner wall of the stator with the assistance of spring tension and centrifugal force and slide in the rotor slot, and when the rotor rotating, the two rotary vanes are always sliding along the inner wall of the stator.

The two rotary vanes divide the crescent-shape space formed by surrounding by the rotor, chamber of stator and fixed cover into three parts A, B and C.

    
 
 When the rotor rotating by the direction shown in the figure, the capacity of space A, which is connected to the air entry, continuously increases, and the pressure in space A continuously gets down. When the pressure in space A is lower than that in the container in which the gas is pumped, according to the principle of gas pressure balance, the pumped gas is continuously drawn into the suction chamber A, that is the pump is in
the process of suction. At this time, the capacity of the space of chamber B is gradually reduced, the pressure continuously increases, that is the pump is in the process of compression. With the capacity of space C which is connected with the air outlet is further reduces, the pressure in space C further increases. When the gas pressure is higher than the exhaust pressure, the compressed gas opens the exhaust valve, and the pumped gas continuously pass through the oil layer of the oil tank to the atmosphere. In the continuous running of the pump, it continuously repeats the process of suction, compression, and exhaust, so as to achieve continuous pumping.

The exhaust valve is immersed in the oil to prevent air flowing into the pump. The oil gets into the pump chamber through the gap on the pump body, oil hole and the exhaust valve, to cover the moving surfaces in the chamber and form the seal of the suction chamber and exhaust chamber; in addition, the oil also full up all the harmful space to remove their impact on the ultimate vacuum.
Two-stage sliding vane rotary vacuum pump consists of two working chambers which are connected in series and rotating at the same speed by the same direction. ChamberⅠis at a low vacuum level, while chamber is at a high vacuum level. The pumped gas enters chamber through  the air inlet. When the intake gas pressure is higher, the gas will be compressed in chamber , so that the pressure rapid increases, and the compressed gas will be not only exhausted from the senior exhaust valve, but also pass through the passage of the intermediate wall and enter chamber ,  then be compressed in chamber and exhausted from the low-level exhaust valve; when the pressure of the gas entering chamber Ⅰis low, despite the gas is compressed in chamber Ⅰ, it still can not open the senior exhaust alue to get out. All the gas enters chamber Ⅰ through the passage of the intermediate wall, and by compressed in chamber Ⅰ, it is exhausted from the low-level exhaust valve. Therefore, the ultimate vacuum of the two-stage sliding vane rotary vacuum pump is higher than that of the single-stage sliding vane rotary vacuum pump.

Range of use


    XD pumps are widely applied to the vacuum packaging of various types of food, paper conveying in printing industry, vacuum suction molding in rubber and plastic industry, vacuum impregnation treatment of various castings, vacuum fixture of engineering industry, vacuum suction in surgeries of hospitals, vacuum power test, etc.

Performances and specifications


 Function Model

(m3/h)
Pumping Speed

≤(Pa)
Ultimate
Pressure

(kw) Motor Power


(rpm)
Rotational
Speed


(L)
Injection
Amount`of Oil

 (in)
Inlet
Diameter

(Kg)
Weight


dB(A) ≤

XD-010

10

200

0.37

1400

0.5

G1/2"

16

69

XD-020

20

200

0.75

2800

0.5

G1/2"

18

71

XD-040

40

200

1.5

1440

1.5

G11/4"

58

75

XD-063

63

200

1.5

1440

2

G11/4"

62

76

XD-100

100

200

3

1440

2.5

G11/4"

89

77

XD-160

160

200

4

1440

9

G2

145

79

XD-250

250

200

7.5

1440

9

G2

200

80


   

Installing dimension drawing


Type 

A

B

C

D

E

F

XD-010

405

265

210

60

210

131

XD-020

430

265

210

60

210

131

XD-040

624

312

280

160

315

183

XD-063

665

330

280

130

364

195

XD-100

725

470

255

211

352

275

XD-160

835

540

410

240

390

304

XD-250

948

540

410

240

516

304


Characteristic curve


 

All rights reserved:Wuxi City Sefang Vacuum Equipment Co.,Ltd         
Add:No.48 Changkang Road, Mashan, Binhu District, Wuxi Tel:0510-85990421 85990035
Technical Support:wxmilai.com 苏ICP备:0510548号